XPH Series

Model: XPH Series
Voltage:18V - 150V
Current: 2A - 10A
Power: 175W - 420W
Overview: Compact, high performance low cost power supply
  • Overview +


    Sorensen XPH Series
    The Sorensen XPH Series provides 175 to 420 watts of DC power. The XPH is a compact, high performance low cost power supply suited for benchtop applications.

    The Sorensen XPH Series uses combined switch–mode pre–regulation with linear post-regulation to provide performance comparable with an all linear design. The XPH features excellent line and load regulation with low noise and good transient response. The XPH Series is available in a single, dual and triple output for benchtop use.

    The Sorensen XPH dual output models have two independent and isolated outputs with its own on–off switch. The outputs can be wired in either series or parallel to provide higher voltage and higher current output. All outputs are instrinsically short circuit proof, and are protected against external voltages and reverse currents. The XPH triple output model has the same features as the dual output model with an additional switchable fixed output of 3.3V and 5V.

    Key Features
    • Low noise

    • Excellent line⁄load regulation

    • Coarse and fine voltage controls

    • Constant voltage or constant current operation with automatic crossover and mode indication

    • Individual ON⁄Off switch per output (not including fixed output)

    • Switchable 3.3V⁄5V output on triple output model

    • Switchable remote sense (XPH 18­10 amd XPH 42­10 models)
  • Specifications +


    Sorensen XPH Series Specifications
    Output : Voltage and Current
    Model Output
    Voltage
    Output
    Current
    Output
    Power
    Outputs
    XPH 18-10 0-18 V 0-10 A 180 W 1
    XPH 20-20 0-20 V 0-20 A 400 W 1
    XPH 35-5 0-35 V 0-5 A 175 W 1
    XPH 35-4D 0-35 V 0-4 A 280 W 2
    XPH 35-4T 0-35 V 0-4 A 305 W 3
    XPH 42-10 0-42 V 0-10 A 420 W 1
    XPH 75-2D 0-75 V 0-2 A 300 W 2
    Output Terminals
    Standard 4mm “touch proof” binding posts/terminals on 0.75”/19mm pitch. Suitable for bare wire, hook terminals or plugs.
    Input
    AC Input 110-240 V ± 10%, 50/60 Hz (XPH 35-5, XPH 35-4D, XPH 35-4T, XPH 75-2D) Factory set: 110-120 Vac ± 10% or 220-240 Vac ±10%, 50/60 Hz Installation Category II (XPH 18-10, XPH 20-20, XPH 42-10)
    Consumption 400 VA (XPH 35-5, XPH 18-10)
    500 VA (XPH 35-4D, XPH 35-4T, XPH 75-2D)
    800 VA (XPH 20-20), (XPH 42-10)
    General Specifications
    Operating Mode Constant voltage or constant current with automatic cross-over and indication
    Voltage Setting By coarse and fine controls
    Current Setting By single logarithmic control
    Output Impedance Typically < 5 mΩ in constant voltage mode. Typically > 50 kΩ (XPH35-4, XPH75-2D), > 20 kΩ (XPH35-5, XPH42-10), > 10 kΩ (XPH18-10) in constant current mode.
    Line regulation < 0.01% of max. output for a 10% line voltage change
    Load regulation < 0.01% of max. output for a 90% load change, < 0.1% (XPH75-2D in Mode C
    Ripple & Noise Typically < 2 mVrms, < 10 mVpk-pk, < 15 mV (XPH75- 2D), <10mVpk-pk for XPH 20-20, CV mode (20 MHz bandwidth)
    Transient Response < 200 μs to within 50 mV of set level for 90% load change (mode A only XPH75-2D)
    Temperature Coefficient Typically < 100 ppm /°C
    Output Protection Outputs will withstand forward voltages up to 40 V (XPH 35-5. XPH 35-4D, XPH 35-4T) or 85V/170V (XPH 75-2D)
    Status Indication Output ON lamps. Constant current mode lamps
    Output Switch Electronic. Preset voltage/current displayed with output off.
    Remote Selection Switch selectable as Local or Remote
    Regulatory CE-marked units meet: EN61010-1 and EN61326
    Meters (main outputs)
    Meter Types Separate four-digit meters for voltage and three-digit meter current with 14 mm (0.56”) LED displays. Reading rate 4/sec
    Meter Resolutions 100 mV, 10 mA
    Meter Accuracy
    Voltage 0.3% ± 1 digit
    Current 0.6% ± 1 digit
    Environmental
    Operating Temperature 5 to 40°C
    Storage Temperature - 40 to 70°C
    Humidity Range 20% to 80% RH
    Cooling Convection (Fan assisted for XPH 42-10 and XPH 20-20)
    Environmental Indoor use at altitudes to 2000 m, Pollution Degree 2
    Physical
    Dimensions
    (H x W x D)
    6.3 x 5.5 x 12.6” (160 x 140 x 320 mm)
    (XPH 35-5, XPH 18-10, XPH 20-20, XPH 42-10)
    6.3 x 10.2 x 12.6” (160 x 260 x 320 mm)
    (XPH 35-4D, XPH 35-4T, XPH 75-2D)
    Weight 6.2 lb (2.8 kg) (XPH 35-5, XPH 18-10)
    7.9 lb (3.6 kg) (XPH 20-20, XPH 42-10)
    9.5 lb (4.3 kg) (XPH 35-4D, XPH 35-4T)
    9.7 lb (4.4 kg) (XPH 75-2D)
  • Diagram +


    Sorensen XT Series Diagram

    Diagram Formats
    PDF XT Diagram (185KB)
  • Manuals +

  • Data Sheets +

  • Get A Quote +


    XPH : Model Number Description



    Options and Accessories
    All Models 4mm safety sockets, suitable for shrouded plugs