Skip to content

BPS Series

Model: BPS Series
Voltage: 150V - 400V
Current: 0A - 400A
Power: 30kVA – 180kVA
Overview: High Power Programmable AC Source for frequency conversion and product test.

  • Overview +

    California Instruments BPS Series

    The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you. Features And Benefits
    Key Features

    • High Power AC Source
    Programmable AC power for frequency conversion and product test applications

    • Expandable Power Levels
    Available output power of 30, 45, 75 and 90 kVA per unit and multi-unit configurations for power requirements up to 180 kVA and above

    • Remote Control
    Standard RS232, USB and IEEE-488 (GPIB) and optional LAN interfaces are available for automated
    test applications.

    Simple Operation
    The BPS Series can be operated completely from its menu driven front panel controller. A backlit LCD display shows menus, setup data, and read-back measurements. IEEE-488, RS232C, USB and LAN remote control interfaces and instrument drivers for popular ATE programming environments are available. This allows the BPS Series to be easily integrated into an automated test system.

    The BPS is capable of delivering 30, 45, 75, 90, 150 or 180kVA of AC power. The 30 and 45kVA models come as dedicated single or three phase output while the 75, 90, 150 and 180kVA models are dedicated three phase. For higher power requirements, simply parallel the BPS in multi-cabinet configuration. Multi cabinet systems always operate in three phase output mode commonly found in power systems.

    Product Evaluation and Test
    Increasingly, manufacturers of high power equipment and appliances are required to fully evaluate and test their products over a wide range of input line conditions. The built-in output transient generation and read-back measurement capability of the BPS Series offers the convenience of a powerful, and easy to use, integrated test system.

    With an output frequency range to 819 Hz, the BPS Series is well suited for aerospace applications. Precise frequency control and accurate load regulation are key requirements in these applications. The available remote control interfaces and SCPI command language provide for easy integration into existing ATE systems. The BPS Series eliminates the need for several additional pieces of test equipment, saving cost and space. Instrument drivers for popular programming environments such as National Instruments LabView™ are available to speed up system integration.

    Choice of voltage ranges
    Standard voltage ranges are 150V L-N (259V L-L) and 300V (519V L-L) and are direct coupled output. For applications requiring more than 300V L-N (or 519V L-L), the optional -HV output transformer provides a third additional 400V L-N and 693 V L-L output range which is internal to the AC chassis. No external magnetics modules are required.

    Multi-Box Configurations
    For high power applications, two BPS75 or BS90 chassis can be combined to provide 150kVA or 180kVA of output power. For higher power requirement please contact sales for custom configurations.

    Simple transition from R&D to Manufacturing.
    The California Instruments Mx and RS Series are high performance, feature rich Research and Development solutions. That level of advanced performance is not always required in production and lab environments. Since the BPS shares common code structure and performance characteristics as the Mx and RS the BPS is ideally suited to easily transition into cost effective production solutions.

    High Crest Factor
    With a crest factor of up to 4.5, the BPS Series AC source can drive difficult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to pull high repetitive peak currents.

    Remote Control
    Standard RS232, USB and IEEE 488 (GPIB) along with optional LAN remote control interfaces allow programming of all instrument functions from an external computer. The popular SCPI command protocol is used for programming.

    Application Software
    Windows® application software is included. This software provides easy access to the power source’s capabilities without the need to develop any custom code. The following functions are available through this GUI program:
    • Steady state output control (all parameters)
    • Create, run, save, reload and print transient programs
    • Measure and log standard measurements
    • Capture and display output voltage and current waveforms.
    • Measure standard power measurements..
    • Display IEEE-488, RS232C, USB and LAN bus traffic to and from the AC Source to help you develop your own test programs.

    BPS Series - AC Transient Generation
    The BPS Series controller has a powerful AC transient generation system that allows complex sequences of voltage and frequency to be generated. This further enhances the BPS’s capability to simulate AC line conditions and disturbances. Transient generation is controlled independently yet time synchronized on all three phases. Accurate phase angle control and synchronized transient list execution provide unparalleled accuracy in positioning AC output events.

    Transient programming is easily accomplished from the front panel where clearly laid out menu’s guide the user through the transient definition process.

    The front panel provides a convenient listing of the programmed transient sequence and allows for transient execution Start, Stop, Abort and Resume operations. User defined transient sequences can be saved to non-volatile memory for instant recall and execution at a later time. The included Graphical User Interface program supports transient definitions using a spreadsheet-like data entry grid. A library of frequently used transient programs can be created and saved using this GUI program.

    BPS Series - Measurement and Analysis
    The BPS Series is much more than a programmable AC power source. It also incorporates an advanced digital signal processor based data acquisition system that continuously monitors all AC source and load parameters. This data acquisition system forms the basis for all measurement and analysis functions. These functions are accessible from the front panel and the remote control interface for the BPS Series.

    Conventional Measurements

    Common AC measurement parameters are automatically provided by the data acquisition system. These values are displayed in numeric form on the front panel LCD display. The following measurements are available: Frequency, Vrms, Irms, Ipk, Crest Factor, Real Power (Watts), Apparent Power (VA) and Power Factor.

    Waveform Acquisition

    The measurement system is based on real-time digitization of the voltage and current waveforms using a 4K deep sample buffer. This time domain information provides detailed information on both voltage and current Waveshapes. Waveform acquisitions can be triggered at a specific phase angle or from a transient program to allow precise positioning of the captured waveform with respect to the AC source output. The front panel LCD displays captured waveforms with cursor readouts. The included GUI program also allows acquired waveform data to be displayed, printed, and saved to disk.
  • Specifications +

    California Instruments BPS Series : Specifications
    Operating Modes
    Standard AC
    AC Mode Output
    Frequency Range: 16.00-819.0 Hz, -LF Option: 16.00-500.0 Hz,
    Resolution: 0.01 Hz: 16.00 - 81.91 Hz, 0.1 Hz: 82.0 Hz - 819.1 Hz
    Phase Outputs 1 or 3 Neutral: Floating, Coupling: DC (except for -HV option) Please specify Single (-1) or Three Phase (-3) for BPS30 and BPS45 at time of order.
    Total Power BPS30-1/3; 30kVA, BPS45-1/3: 45kVA, BPS75-3: 75kVA, BPS90-3: 90kVA, BPS150-3:150kVA, BPS180-3, 180kVA
    Load Power Factor 0 to unity at full output current
    AC Mode Voltage
    Voltage Ranges
    Range VLow VHigh
    AC 0-150 V 0-300 V
    Load Regulation < 0.25 % FS to 100 Hz, < 0.5 % FS 100 Hz to 819 Hz
    Line Regulation < 0.1% FS for 10 % line change
    External Sense Voltage drop compensation (5% Full Scale)
    Harmonic Distortion (Linear) Less than 0.5% from 16 - 66 Hz, Less than 1% from 66 - 500 Hz, Less than 1.25%
    above 500 Hz
    DC Offset < 20 mV
    Load Regulation 0.25% FS @ - 100 Hz, 0.5% FS > 100 Hz
    External Amplitude Modulation Depth: 0 - 10 %, Frequency: DC - 2 KHz
    Voltage slew rate 200 μs for 10% to 90% of full scale change into resistive load, 0.5V / μSec
    AC Mode Current
    BPS30-1/3 - 30 KVA BPS30-1 V Lo:200A, V Hi: 100A, Single phase
    BPS30-3, V Lo: 66.7A, V Hi: 33.3A, per phase 3 phase
    BPS45-1/3 - 45 KVA BPS45-1 V Lo:300 A, V Hi: 150A, Single phase
    BPS45-3 V Lo: 100, V Hi: 50A, per phase 3 phase
    BPS75 - 75 KVA BPS75, V Lo: 166A, V Hi: 83A per, phase
    BPS90 - 90 KVA BPS90, V Lo:200A, V Hi: 100A per phase
    BPS150 -150 KVA BPS150, V Lo:332A, V Hi: 166A per phase
    BPS180 - 180 kVA BPS180, V Lo:400A, V Hi: 200A per phase
    Note: Constant power mode provides increased current at reduced voltage. See chart below
    Peak Repetitive AC Current Up to 3.6 x rms current at full scale voltage
    Programming Accuracy Voltage (rms): ± 0.3 Vrms, Frequency: ± 0.01 % of programmed value, Current Limit: - 0 % to + 5 % of programmed value + 1A, Phase: < 0.5° + 0.2°/ 100 Hz with balanced load
    Programming Resolution Voltage (rms): 100 mV, Frequency: 0.01 Hz from 16 - 81.91 Hz, 0.1 Hz from 82.0 - 819 Hz, Current Limit: 0.1 A, 3 phase mode, 1.0 A, 1 phase mode, Phase: 0.1°
    Constant Power AC Mode
    Measurement Specifications
    Parameter Range Accuracy* (±) Resolution*
    Frequency 16-100 Hz
    100-820 Hz
    0.01% + 0.01 Hz 0.01 Hz /
    0.1 Hz
    RMS Voltage 0-400 V 0.05 V + 0.02%
    0.1 V + 0.02%
    10 mV
    RMS Current 0-300 A 0.15 A + .02%
    0.3 A + .02%
    10 mA
    Peak Current 0-800 A 0.15 A + 0.02%
    0.3 A + .02%
    10 mA
    Crest Factor 0.00-6.00 0.05
    Real Power 90 kW 30 W + 0.1%
    60 W + 0.1%
    10 W
    Apparent Power 90 kW 30 VA + 0.1%
    60 VA + 0.1%
    10 VA
    Power Factor 0.00-1.00 0.01
    Phase 0.0-360.0 2.0°
    * Measurement system bandwidth = DC to 6.7 kHz. Accuracy specifications are valid above 100 counts. Current and Power Accuracy and Range specifications are times three for BPS 150 and BPS180 in single phase mode. PF accuracy applies for PF > 0.5 and VA > 50 % of range
    Over Load Constant Current or Constant Voltage mode
    Over Temperature Automatic shutdown
    Non Volatile Mem. storage 16 instrument setups, 200 user defined waveforms [Pi only]
    Waveform Types Std: Sine Wave
    System Interface
    Inputs Remote shutdown
    Outputs Function Strobe / Trigger out
    Remote Control
    IEEE-488 Interface IEEE-488 (GPIB) talker listener. Subset: AH1, C0, DC1, DT1, L3, PP0, RL2, SH1, SR1, T6, IEEE-488.2 SCPI Syntax
    RS232C Interface 9 pin D-shell connector (Supplied with RS232C cable)
    LAN ( option ) Ethernet Interface: 10BaseT, 100BaseT, RJ45
    USB Version: USB 1.1; Speed: 460 Kb/s maximum
    Output Relay Push button controlled or bus controlled output relay
    AC Input
    Voltage Must be specified at time of order. All inputs are L-L, 3ø, 3 wire + Gnd. 208 ± 10% VAC, 230 ± 10% VAC, 400 ± 10% VAC, 480 ± 10% VAC
    Input Line Current (per phase)
    BPS30-1/3 116 ARMS @ 187 VLL
    105 ARMS @ 207 VLL
    60 ARMS @ 360 VLL
    50 ARMS @ 432 VLL
    BPS45-1/3 175 ARMS @ 187 VLL
    157 ARMS @ 207 VLL
    90 ARMS @ 360 VLL
    75 ARMS @ 432 VLL
    BPS75 285 ARMS @187 VLL
    256 ARMS @ 207 VLL
    147 ARMS @ 360 VLL
    122 ARMS @ 432 VLL
    BPS90 350 ARMS @ 187 VLL
    314 ARMS @ 207 VLL
    180 ARMS @ 360 VLL
    150 ARMS @ 432 VLL
    BPS150 Each BPS75 chassis requires its own AC service. Total Line currents are 2 x BPS90
    BPS180 Each BPS90 chassis requires its own AC service. Total Line currents are 2 x BPS90
    Distortion: < 8 % at full power < 20 % below 35 % of power
    Line Frequency 47 - 63 Hz
    Efficiency 85 % typical
    Power Factor 0.95 typical
    AC Service
    Inputs/Outputs Rear panel connection
    Regulatory IEC61010, EN50081-2, EN50082-2, CE EMC and Safety Mark requirements
    EMI CISPR 11, Group1 , Class A
    Connectors AC Input & Output terminal block behind front cover, IEEE-488 (GPIB) connector (rear panel), 9 pin D-Shell RS232C connector*, (rear panel), Remote voltage sense terminal block (rear panel), System Interface Connector, DB-37 (rear panel). *RS232 DB9 to DB9 cable supplied
    Physical Dimensions
    BPS30/45 Dimensions Height: 50” 1270 mm, Width: 28.75” 731mm, Depth: 34.5” 876mm
    BPS30/45 Weight Per Chassis: Net: 1150 lbs / 522 Kg approximately, Shipping: 1231 lbs / 560 Kg approximately
    BPS75/90 Dimensions Height: 76” 1930 mm, Width: 32.0” 812mm, Depth: 40.0” 1016mm
    BPS75/90 Weight Per Chassis: Net: 1650 lbs / 748 Kg approximately, Shipping: 1731 lbs / 785 Kg approximately
    Chassis Casters and forklift openings.
    Vibration and Shock Designed to meet NSTA project 1A transportation levels. Units are shipped in wooden crate with forklift slots
    Air Intake/Exhaust Forced air cooling, front air intake, rear exhaust
    Operating Humidity 0 to 95 % RAH, non condensing
    Temperature Operating: 0 to 40° C (30° C max in CP mode), Storage: -20 to +85° C
  • Diagram +

    California Instruments BPS Series : Diagram

  • Data Sheets +

  • Manuals +

  • Firmware Updates +

  • Software +

  • Instrument Drivers +

  • Get A Quote +

    BPS Programmable AC Source
    Model AC output Power Phase Outputs AC Voltage Range (L-N)
    BPS30-1 30kVA 1 150/300
    BPS45-1 45kVA 1 150/300
    BPS30-3 30kVA 3 150/300
    BPS45-3 45kVA 3 150/300
    BPS75-3 75kVA 3 150/300
    BPS90-3 90kVA 3 150/300
    BPS150-3 150kVA 3 150/300
    BPS180-3 180kVA 3 150/300
    Models incldue RS232, USB, IEEE-488 (GPIB) and optional Ethernet (LAN) interfaces
    Controller Options
    Option Code Description
    -LF Limits maximum frequency to 500 Hz.
    -FC Modifies output frequency control to ± 0.25%.
    -LAN Ethernet Interface.
    -HV Adds 400 V L-N AC-only output range.
    Mode Features
    AC Mode
    Dual Voltage Range
    Transient Programming
    RS232, USB, IEEE-488 (GPIB)
    Supplied With
    Users Manual
    Users Programming Manual
    Graphical Users Interface Software
    Packaging and Shipment
    All BPS products are shipped with re-usable protective